For Windows desktops, there is a simple programme called Xiaomi Flashing Interface. It enables users to flash Xiaomi devices in fastboot and EDL modes. A few of the additional models permit flashing without identification. All users can use it for free. There is no need for you to buy any licences. Run it on a Windows PC after installing it.
Changelog!!!
Xiaomi Flashing Interface v1.0
Feature:
- – MD5 Files Checksum
- – Fastboot Flash
- ” Xiaomi EDL Flash without Auth
- – EDL Flash
- ” EDL Single Raw FlashEDL Flash [Single Raw
- — EDL Flash (Multi Raws[Multi Raws
- — Muti Devices Flash
EDL without Flash Auth Tested:
- – Redmi 7A
- – Redmi 8
- – Redmi 8A
- Redmi Note 8 / Redmi Note 8
EDL without Auth that is supported by Devices:
- – Pocophone F1 (Beryllium)
- • Pocophone M3 (Citrus)
- Blackshark 3 Pro – Blackshark 3 Pro
- Blackshark 3 – Blackshark 3
- – Redmi Note 9 4G/ Redmi 9T (lime)
- — Redmi Note 8 (ginkgo)
- — Redmi Note 8T (willow)
- – Redmi Note 5 Pro (whyred)
- – Redmi Note 6 Pro (tulip)
- – Redmi Note 7 Pro (violet)
- – Redmi Note 7 (lavendar)
- Mi8 (dipper)
- Mi8 Lite (platina)
- – Mi 8 SE(srius)
- – Mi 8 EE(equuleus)
- Mi 8 Pro/UD(ursa)
- Mi 9 SE (grus)
- Mi CC9 (pyxis)
- – Mi CC9E (laurus)
- Mi 6X (wayne)
- – Mi Max 3 (nitrogen)
- Mi 5X (tiffany)
- – Mi A2 Lite (daisy)
- – Redmi 6 Pro (sakura)
- — Redmi 7A (pine)
- — Redmi 8. (olive)
- ” Redmi 8A (olivelite)
- The Redmi 8 Pro Dual (olivewood)
- Redmi S2 (ysl) Redmi S2 (ysl)
How Do I Use?
- You must first download the ZIP file by clicking the link provided.
- After that, you must unzip every file on drive c: (important)
- Before beginning the installation, make sure that your antivirus software is switched off.
- The setup file should then be opened and installed by following the simple steps.
- Run the "Xiaomi flashing interface.exe" software.
- If you already have drivers installed, you will need to instal them all again after that. Skip this step if you don't.
- The next action is to boot the device in Fastboot or EDL. After that, load the firmware file, choose "FLASH," and press "FLASH."
- Use the phone's internet connection to try out any task.
- Enjoy !!!
Obtaining the Xiaomi Flashing Interface
Follow these instructions to get the Xiaomi Flashing Interface V1.0 4 Qualcomm Tool:
1. Visit the "Support" page on the official Xiaomi website.
2. Look for the "Xiaomi Flashing Interface V1.0 4 Qualcomm Tool" link under the "Downloads" section.
3. After you click the link, the download will begin immediately.
4. Unzip the package and launch the "Xiaomi Flashing Interface" folder when the download is finished.
5. To run the utility, double-click the "XiaomiFlashing.exe" file.
6. To finish the flashing procedure, adhere to the on-screen instructions.
the setup document You must open the tool and follow the instructions when the setup is finished.